How to Install a Ghost Immobiliser
Ghost immobilisers are hidden security system that protects your vehicle from hacking and key cloning. It stops the engine from starting until a PIN code is entered. This could be as long as 20 characters.
This additional layer of security is not detectable by thieves who might not be aware of it. Certain systems also come with an application that lets owners disable the immobiliser in the event that they forget their PIN, or to use the service/valet mode.
Connecting to the vehicle's CAN bus
The Ghost 2 Immobiliser, a cutting edge security system, is able to be integrated directly into the ECU of your vehicle. It offers a discrete protection against thieves. It is extremely efficient and user-friendly and can be a valuable component of your vehicle's security arsenal. Like any anti-theft device, it's not foolproof and requires regular maintenance in order to function properly. Fortunately, this guide can help you get the most benefit from the Ghost 2 Immobiliser.
CAN (Controller Area Network) is a robust serial network that lets microcontrollers communicate with each other across short distances without the need for central control units. It is designed to multiplex electrical wiring within vehicles to save on copper and comes with a variety of advantages, including low costs and easy use.
The CAN protocol is utilized in the majority of modern cars to communicate with the engine management system, transmission controller, steering control module and air conditioning controls and more. It also transmits sensor data, such as inputs and speed sensors, to control the various functions of the vehicle. The CAN bus is used to monitor these diverse components, and prevent a vehicle from starting if they are in an unsafe state.
Although the CAN bus can be utilized for a variety of purposes, it's important to understand how it works and how it's secured. It is possible to add additional features to a vehicle by using CAN bus, but it is important to protect it against attacks from hackers and other dangers. The best way to do this is by installing a firewall and monitoring your CAN bus through software.
Ghost2's control device is hidden in the dashboard of the car or in the wiring harness, preventing a thief from physically tampering it. It is also impossible to reset a PIN or emergency code without having access to the car.
You can activate Transport Mode when you have to sell your car for service, valet parking or for any other reason. This feature disables both the keyfob as well as the ignition functions of the Ghost immobiliser. It will only reactivate after the vehicle has travelled 31 mph for a time of 15 minutes.
How to create a PIN code
The Ghost immobiliser protects your car from theft. ghost immobiliser cost utilizes the PIN to disable the engine of the vehicle and stop it starting without the correct code, or a valid fob or mobile. Its discrete design ensures the system is inconspicuous and offers unparalleled security against theft. Additionally the system is TASSA verified and can lead to significant savings on insurance premiums for cars.
During the installation, the Ghost system enters an learning mode that records the sequence of buttons pressed to generate your unique pin code. After the pin code is created and the installer has completed its work, it will guide you through the steps to activate the system. Once activated, the Ghost system shuts down your vehicle's starting motor until you enter a valid PIN or switch the vehicle to transport mode. This makes it extremely difficult for thieves or cloners to hack or clone your vehicle's starter system.
It's easy to set up a Ghost immobiliser, however, you must follow the precise instructions included in the user's guide to ensure the proper operation. Hand tools and multimeters can be used to verify electrical values. Insulation tape, heat shrink tubing and cable ties can be utilized to shield exposed wiring. Be sure to test the system on a regular basis to find any issues or potential mistakes.
After the installation is completed, it is important to perform a final check of the system before turning on the ignition in your vehicle. Ghost immobilisers will arm themselves after 3 to 30 seconds, dependent on the model of your car. The system also comes with a Service/Valet mode that allows you to temporarily disable the system while you are servicing your vehicle or valet parking.
Ideally, the immobiliser should be hidden in an inconspicuous location under the dashboard or steering wheel. It is recommended to use a small piece of paint or duct tape to mark the CAN H and CAN L wires, so that you can easily find them when you are testing. The CAN H and L wires must also be connected to an electrical source that provides a constant 12V. It is also essential to check the connections again after testing, since misidentifying these wires could cause the system to fail.
The system must be activated
A ghost immobiliser stops your car from starting unless you press a set of buttons inside the vehicle typically the steering wheel, door panel, or central console. The sequence can be changed by the user if needed. Once activated, the system will not be turned off. This makes it a great choice for those who want to safeguard their vehicle from theft.
The device is not designed to be able to be detected by modern diagnostic tools and code-grabbing technology. It also doesn't broadcast out radio frequencies, which makes it even difficult for thieves to identify the device.
If the device is discovered it will stop the engine from starting. It will also sound an alarm to scare the burglar away. The device can also be used to track the location of the vehicle and help police track it down when it is stolen.
If you're interested in a ghost immobiliser, contact the experts at Car Specalist Customs to get an estimate and discuss your options. We are able to install ghost immobilisers on your vehicle. Ghost 2 immobiliser will make sure that it is placed in a location that is difficult to reach. We can also install other security measures, like the kill switch and wheel lock, to ensure your vehicle is secure from theft.
Disarming the System
If you own an Ghost immobiliser that is fitted to your vehicle, it's essential to know how to disarm it. conversational tone can be used in the event that you lose your keys or your battery dies. The system uses an unique PIN code that only you know. It will not start the vehicle without this code. Pressing a combination buttons on the steering wheel or on the dashboard is the easiest method of entering your code. This is a far simpler method than using the key fob and it also prevents anyone from copying your remote.
Ghost2 isn't intrusive unlike some aftermarket immobilisers that require cutting wires for installation. It also works with the CAN bus system of your vehicle to operate. Its most prominent feature is that it shuts off the engine without affecting functions of the vehicle. This makes it difficult for thieves to use signal boosters or to clone keys for cars. It doesn't emit radio frequency, therefore thieves won't be able to detect it.
The Ghost system has an option called Transport Mode that lets you temporarily disable security for situations such as transportation or service. This feature is useful for when you're loaning your vehicle to someone else without sharing your PIN code, or if your vehicle requires to be secured while you drive it. To activate the Transport Mode you need to press the service button five times within a period of 2 seconds. The Ghost system will confirm activation using 5 indication signals.
Keep the emergency code inside your vehicle in a safe location. If you ever find yourself locked out of your car, you can call the company or technician who installed the system, and they'll provide you with the code. If you are unable reach them, then you can contact an authorized dealer. However, this might require verification procedures and you may be charged additional fees.
Aside from the convenience of this system, you can also count on it to guard your vehicle from theft and reduce insurance costs. Numerous insurance companies offer reduced premiums or financial incentives to install this anti-theft system.